M3T-SSOP36B-450
Dummy IC for 36-pin 0.8-mm-pitch SSOP
User’s Manual
Keep safety first in your circuit designs!
z Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products
better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to
personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with
appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention
against any malfunction or mishap.
Notes regarding these materials
z These materials are intended as a reference to assist our customers in the selection of the Renesas Technology product best suited
to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to
Renesas Technology Corporation, Renesas Solutions Corporation or a third party.
z Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage, or infringement of
any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application
examples contained in these materials.
z All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information
on products at the time of publication of these materials, and are subject to change by Renesas Technology Corporation and
Renesas Solutions Corporation without notice due to product improvements or other reasons. It is therefore recommended that
customers contact Renesas Technology Corporation, Renesas Solutions Corporation or an authorized Renesas Technology product
distributor for the latest product information before purchasing a product listed herein. The information described here may contain
technical inaccuracies or typographical errors. Renesas Technology Corporation and Renesas Solutions Corporation assume no
responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information
published by Renesas Technology Corporation and Renesas Solutions Corporation by various means, including the Renesas home
page (http://www.renesas.com).
z When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and
algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the
information and products. Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any
damage, liability or other loss resulting from the information contained herein.
z Renesas Technology semiconductors are not designed or manufactured for use in a device or system that is used under
circumstances in which human life is potentially at stake. Please contact Renesas Technology Corporation, Renesas Solutions
Corporation or an authorized Renesas Technology product distributor when considering the use of a product contained herein for any
specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
z The prior written approval of Renesas Technology Corporation and Renesas Solutions Corporation is necessary to reprint or
reproduce in whole or in part these materials.
z If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from
the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport
contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
z Please contact Renesas Technology Corporation or Renesas Solutions Corporation for further details on these materials or the
products contained therein.
Precautions to be taken when using this product
z This product is a development supporting unit for use in your program development and evaluation stages. In mass-producing your
program you have finished developing, be sure to make a judgment on your own risk that it can be put to practical use by performing
integration test, evaluation, or some experiment else.
z In no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this product.
z Renesas Solutions Corporation strives to renovate or provide a workaround for product malfunction at some charge or without charge.
However, this does not necessarily mean that Renesas Solutions Corporation guarantees the renovation or the provision under any
circumstances.
z This product has been developed by assuming its use for program development and evaluation in laboratories. Therefore, it does not
fall under the application of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when
used in Japan.
If the requirements shown in the "CAUTION" sentences are ignored,
the equipment may cause personal injury or damage to the products.
CAUTION
Rev.1.00
September 1, 2003
REJ10J0212-0100Z
(1/4)
6. External Dimensions of the M3T-SSOP36B-450
Symbol Dimension (mm)
HD
A
b
4.2
D
A
0.3
8.4
1
40
D
1
36
E
e
15.0
0.8
b
e
HD
12.4
E
1
40
Upper connector J1:
J
18
19
20
21
AXK5S40045P
1
(made by Matsushita Electric Works, Ltd.)
20
21
Board
Pin
Material: Glass epoxy board
Material: Bronze phosphide
1
1
: Pin No. of the M3T-SSOP36B-450
: Pin No. of the upper connector
Plating:
Solder plating
Material: Heat tolerant resin (body)
Copper alloy (post, contact)
Upper connector
(J1)
Plating:
Nickel-based gold plating
Figure 3 External dimensions of the M3T-SSOP36B-450
7. Sample Foot Pattern of the Target System
0.80±0.05
13.6±0.1
0.20±0.05
+0.1
-0
0.4
0.80±0.05
Unit: mm
Figure 4 Dimensions of a target foot pattern (Quoted from the specifications of IC socket for SSOP by Matsushita Electric Works, Ltd.)
(3/4)
8. Precautions
CAUTION
Cautions to Be Taken for This Product:
z Do not solder the M3T-SSOP36B-450 main unit directly on a target board. Be sure to use the included socket.
z Before mounting the M3T-SSOP36B-450, be sure to check the pin positions.
z For soldering the socket and mounting the M3T-SSOP36B-450, refer to the supplementary document “Mounting the
Socket Included with the M3T-SSOP36B-450” and “Notes on Handling the M3T-SSOP36B-450”.
z Do not apply unnecessary stress to the M3T-SSOP36B-450.
z Do not touch the pins of the M3T-SSOP36B-450.
zStore the M3T-SSOP36B-450 in the dedicated case.
IMPORTANT
Notes on This Product:
z We cannot accept any request for repair.
z To remove the socket frame, use the dedicated tool AXY89406301 made by Matsushita Electric Works, Ltd. To
purchase this product and the socket frame for repair, contact Matsushita Electric Works, Ltd.
zFor inquiries about this product or the contents of this manual, contact your local distributor.
9. Correspondence of Connector J1
Table 2 Correspondence of the M3T-SSOP36B-450 and connector J1
Connector pin No. Pin No. of M3T-SSOP36B-450 Connector pin No. Pin No. of M3T-SSOP36B-450
J1-1
J1-2
J1-3
J1-4
J1-5
J1-6
J1-7
J1-8
J1-9
J1-10
J1-11
J1-12
J1-13
J1-14
J1-15
J1-16
J1-17
NC
1
2
3
4
5
6
7
8
J1-21
J1-22
J1-23
J1-24
J1-25
J1-26
J1-27
J1-28
J1-29
J1-30
J1-31
J1-32
J1-33
J1-34
J1-35
J1-36
J1-37
J1-38
J1-39
J1-40
NC
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
NC
9
10
11
12
13
14
15
16
17
18
NC
J1-18
J1-19
J1-20
(NC: No connection)
(4/4)
|